If your tufting gun won’t cut yarn, the first clue is usually on the front of your fabric: loops appear where you expected soft, separated cut pile. It is tempting to turn a screw and try again, but a failed cut does not point to one universal adjustment. First, check whether your gun is meant to cut, then work through the simple checks you can make safely.
KakaoTalk Photo 2024 01 23 15 11 39 020

First, is your gun supposed to cut the yarn?

A dedicated loop-pile gun does not cut each stitch; the yarn is cut manually at the end of a line. If you use a gun that can switch between cut and loop pile, confirm its current setup using the instructions for your exact model. Our guide to cut-pile and loop-pile tufting guns explains the difference.
If the gun is set up for cut pile but still leaves loops, stop and inspect it before tufting more of your rug.
tufting gun not cutting safe checks
The short version: confirm the pile mode, disconnect the power, look for trapped fibers, then test with a yarn suitable for your model. If cutting still fails, consult the model’s support guidance.

Notice what happens when the cut fails

Are all the stitches left as loops, or does the gun cut some stitches but miss others? Does the mechanism move normally? These observations will help you narrow down what to check—and give the manufacturer or seller useful information if you need support.
tufting gun not cutting symptom guide
Uncut loops are a reason to check the pile mode first. Intermittent cuts call for a look at fiber buildup and yarn compatibility. If the gun stops moving or makes a grinding sound, stop using it and seek support.

What to check, in order

1. Disconnect the power before inspecting the cutting area

Unplug the gun—or remove its battery, if applicable—before bringing your hands or a brush near the needle and scissors. Do not reach into the cutting area while the machine is connected to power.

2. Look for loose fibers around the scissors

Yarn fibers can collect in the scissor channel and interfere with the cut. With the power disconnected, gently remove accessible lint using the cleaning method recommended for your machine. Do not force a tool between the blades or take the mechanism apart unless your model’s instructions tell you to.
If you can see a bent or damaged part, leave the gun off and ask the manufacturer or seller for guidance.
[PHOTO 2 — DETAIL: The gun switched off and disconnected, with a clear view of the cutting area. Alt text: “Inspecting a tufting gun’s scissor area with the power disconnected.”]

3. Try a small swatch with a yarn that has cut cleanly before

Some yarns bend against the scissors instead of cutting cleanly. After cleaning and fully reassembling the gun, test on scrap backing with a yarn and setup that previously worked with this machine. Keep your hands clear of the moving parts.
If one yarn cuts and another does not, record the difference before changing the machine. The test does not prove that the scissors are perfect, but it gives you a useful clue.

4. Think back to the last change you made

Did the problem begin just after changing pile height or adjusting the gun? Those settings can affect how a particular model’s scissors operate. Do not copy a screw position or measurement from a tutorial for a different gun. Check your own manual or ask the seller for model-specific instructions.
If the gun still will not cut after the basic checks, its scissors or another cutting component may need adjustment or replacement. Send support the model name, a photo of the resulting stitches, and a note about when the problem started.

What not to do

Do not keep tufting over a failed section hoping the next pass will fix it. Do not test blade movement with your fingers, and do not treat sharpening or turning random screws as a universal repair. A small test swatch is much easier to assess than a half-finished rug.
Routine cleaning can help you spot buildup before it interrupts a project; our tufting gun maintenance guide covers the broader care routine. If your yarn snaps mid-line rather than remaining in uncut loops, that is a different symptom—start with our guide to yarn breaking while tufting.
A clean cut begins with knowing what your particular gun is designed to do. Check the mode, disconnect the power, clear accessible fibers, and test one variable at a time. If the problem persists, the right next step is guidance for your model, not guesswork.
Explore And-et’s tufting supplies on Amazon, or see the finished pieces in our Etsy shop.

Leave a Reply